Electrostatic Generator

High voltage electrostatic generator ST4001A

Electrostatic electret rod ST508A

Product Introduction

ST4001A electrostatic generator rod is a kind of special equipment for static electricity generation. It has the characteristics of simple installation, stable operation and fast static electricity generation. It is especially suitable for various electrostatic destruction experiments in laboratories and various winding machines and production lines.

Action Principle

The ST4001A electrostatic generator can output positive high voltage up to -30Kv, and the output can be continuously adjusted. A large number of positively charged air masses are generated by the static electricity generating rod, and these charged air masses will diffuse around due to the repulsion of the same charges, causing objects close to them to be charged.

Product Features

Stable working performance.

Simple and convenient installation.

Output voltage is continuously adjustable.

Installation Diagram

Product Parameter

30KV Parameter

60KV Parameter

Instructions for Use of Electrostatic Generator

1. Main Points

The electrostatic generator consists of a high voltage generator and a discharge rod.

Please read this manual carefully before installing and using this product.

Please follow the requirements of this manual to avoid damage, loss and risk.

2. Safety

Do not use it in flammable and explosive environment.

For safe and correct operation, please ensure that the equipment is grounded reliably.

The high-voltage generator is used to supply high voltage to the discharge rod, and its electrode

discharges.

Don't point the electrode at the human body; Do not touch the electrodes to avoid electric shock.

3. Use and Operation

The high voltage generator and the discharge rod constitute an electrostatic discharge system.

The output voltage of the high voltage generator is 0~40Kv.

The high voltage generator is connected with relay and photoelectric switch to realize remote

 control of high voltage output.

4. Product Parameters (See Above)

5. Installation

5.1 Check

Check whether the high voltage generator is intact.

Check whether the packing accessories are complete.

If you have any questions or questions, please contact the seller.

5.2 Grounding

Warning:

To ensure safety and normal operation of equipment, please ensure reliable grounding of

equipment.

5.3 Installation

Warning:

Do not install the high-voltage generator in a damp, dirty, flammable and explosive environment.

The high voltage generator must be installed in a place without vibration.

1. The high-voltage generator shall be installed at a convenient location and as close as possible to

the discharge rod.

2. If necessary, use screws to fix the high voltage generator.

3. Connect the grounding wire to the grounding post.

4. Plug the discharge rod into the output jack of the high voltage generator and lock it with its own

nut.

4. Turn the [ON/OFF] switch to the OFF position.

2. Plug the power cord connector into the power interface on the back of the high voltage

generator.

3. Plug the power cord into a grounded power outlet.

4. Plug the aviation handle into the aviation socket and lock it with its own nut.

5. The installation distance of 5cm~10cm can be adjusted according to the actual situation

Note:

High-voltage lines must not touch sharp metal parts or bends.

High voltage lines should be separated from low voltage lines.

The shorter the high-voltage line, the better.

6. Use 

6.1 Power on and off

Energize = [ON/OFF] switch is in [ON] position.

Power outage = [ON/OFF] switch is in [OFF] position.

6.2 Start and stop high voltage output

Start high voltage output = two leads of aviation plug are connected.

Stop high voltage output = two leads of aviation plug are disconnected.

6.3 Set the output voltage

Note:

The output voltage of high-voltage supply should meet the requirements. If the voltage is too high,

ignition and breakdown will occur, which will affect the normal operation of equipment and have

potential safety hazards.

High-voltage supply is equipped with large-capacity capacitor inside. When the high-voltage

supply is cut off, it is necessary to stop the machine for enough time or ground the electrode with

wire to discharge before touching the discharge needle.

Increase the output voltage = transfer the voltage adjustment knob clockwise.

Lowering the output voltage = transferring the voltage adjustment knob counterclockwise.