Recommended today - Small flow type ion nozzle length can be customized with electrostatic eliminator rods
ST-DC-506A Air Source DC Ion Bar
Built-in type of high voltage power supply equipped with HDC-AC
HDC-AC technology provides long-term stability in static elimination without the need for cleaning over the long term.
30% improvement in static elimination times and products sizes over existing models!
Main features
HDC-AC technology provides stable and long-term static elimination capabilities .we have designed an ionizer that does not require cleaning over the long term.
1. 30% increase in capabilities
2. Long-term stability of static elimination capabilities
3. Decrease in emitter needle abrasions
4. Ultra low ozone
5. Superior ion balance
6. Minimum flow type nozzle
7. Cleaning timer
8. Emitter needle variations
9. Safety features
● The time and size of static electricity removal are increased by 30% (compared with the traditional products of our company)
ST-DC-506A is the successor model of our company's traditional product ST503A. The static electricity removal time is increased by more than 30%, and it is more miniaturized. It is an ionizer with the industry's top static electricity removal performance.
l Small-flow discharge needle nozzle for suppressing air consumption is easy to replace
There are also two kinds of discharge needle nozzles, i.e., normal air consumption nozzles and small flow nozzles which can restrain compressed air consumption. The nozzle can be conveniently replaced.
l The cleaning timer function notifies the cleaning time
When the timer reaches the preset value, the LED lights up to inform that it is time to clean the discharge needle. The time until lighting can be set by the user. (100 to 10000 hours, 9 modes, can also be set to no lights.)
l Ensure safety
Through micro-discharge detection and low-voltage wiring of DC24V input, the use safety is ensured
Product standard
Product parameter
Product model | ST-DC-506A |
Ion generation mode | Corona discharge mode (HDC-AC) |
Input voltage | DC 24V+5V |
Power consumption | 3.6VA |
Output voltage | 10kV0-P(0 to peak) |
Output when abnormal | No voltage contact output (by normally closed MOSFET relay) |
Measure | D29xH92xW350~3100mm |
Supply pressure range | Under 0.5Mpa |
Ionic equilibrium | ≤+-30V (when the air pressure is 0.3Mpa away from 300mm) |
Work environment | Ambient temperature: 5~40℃ Ambient humidity: 15%~85% (no condensation) Supply gas: clean and dry air |
Attachment | Operating instructions, mounting bracket, power and signal cable (3m), intermediate bracket (over 110mm) |
Indicator panel
Meaning of each indicator light
POWER: Green LED lights up when the power is turned on normally
RUN: Green LED lights up during normal operation
ALARM: The red LED lights up when micro-discharge occurs in the high-voltage part of the main body such as the discharge needle or overcurrent occurs in the main circuit
CLEANING: When the accumulated running time set with T-SELECT exceeds, the yellow LED lights up until it is released with RESET button
TIMER RESET: This button is used to turn off the CLEANING LED
T-SELECT: This selector is used to set the cumulative continuous time for lighting CLEANING LED
Dimensional drawing
Electrostatic removal characteristics
Operating data
Built-In Type of High Voltage Power Supply Equipped With HDC-AC
1. Static Electricity Can Be Removed Uniformly and Stably in the Whole Region
A large amount of positive and negative ions are uniformly supplied in the whole static removing area all the time, and the static removing difference of each area is very small, which is most suitable for electronic equipment requiring fine static removing, etc.
2.Safety Function of Detecting Abnormal Discharge and Spark
It is a safety function of automatically cutting off the applied high voltage after detecting abnormal high voltage discharge such as short circuit of discharge needle of ionizer.
3. Reduce Air Consumption (※ When Using Small Flow L Nozzle)
The original nozzle shape greatly reduces the air consumption (60% less than our products).
Support strong and stable static removal. The nozzle structure is designed to be replaceable, detachable.
You Can Choose From two Kinds of Nozzles According to the Application:
Options That Support Refreshing Static Removal
l AC adapter for ST101BS: ST101BS-DA (Input voltage AC100V~240V)
l Intermediate bracket: ST101BS-SUSP-A (Standard equipment above 1100)
l Power and signal extension cables: ST101BS-ENC3M (length: 3 m)
l Low flow type l nozzle
Specification of tungsten discharge needlST101BS-NDL-LW01
l High-flow H nozzle
Specification of tungsten discharge needle: ST101BS-NDL-HW01
